Re: [PVE-User] PVE 7 & LACP

From: Gilberto Ferreira <gilberto.nunes32@gmail.com>
To: uwe.sauter.de@gmail.com
Cc: Proxmox VE user list <pve-user@lists.proxmox.com>
Subject: Re: [PVE-User] PVE 7 & LACP
Date: Wed, 21 Jul 2021 13:41:08 -0300	[thread overview]
Message-ID: <CAOKSTBuikM5sdbWPjnZm7L79-aGZ+5fLHxJNM5hxkbwkJhS1ig@mail.gmail.com> (raw)
In-Reply-To: <d4ee20fa-93ae-1c64-8855-411c7f337fbc@gmail.com>

So did you solve the issue?
---
Gilberto Nunes Ferreira
(47) 99676-7530 - Whatsapp / Telegram

Em qua., 21 de jul. de 2021 às 12:49, Uwe Sauter <uwe.sauter.de@gmail.com>
escreveu:

> Hi Gilberto,
>
> thanks for that tip. Unfortunately the network configuration quits a few
> steps before the bridge is
> configured. The needed bond0 is not created…
>
>
> Regards,
>
>         Uwe
>
>
> Am 21.07.21 um 17:45 schrieb Gilberto Ferreira:
> > Perhaps you need to change or add this feature in the network interface
> file:
> >
> >
> https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> > <
> https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> >
> >
> >
> >
> > ---
> > Gilberto Nunes Ferreira
> > (47) 99676-7530 - Whatsapp / Telegram
> >
> >
> >
> >
> >
> >
> > Em qua., 21 de jul. de 2021 às 12:18, Uwe Sauter <
> uwe.sauter.de@gmail.com
> > <mailto:uwe.sauter.de@gmail.com>> escreveu:
> >
> >     Hi all,
> >
> >     Fresh installation of PVE 7 with all available updates.
> >
> >     It looks like I'm unable to configure bonding of two interfaces
> using LCAP.
> >
> >     Output from "ip a":
> >     1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
> group default qlen 1000
> >         link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> >         inet 127.0.0.1/8 <http://127.0.0.1/8> scope host lo
> >            valid_lft forever preferred_lft forever
> >         inet6 ::1/128 scope host
> >            valid_lft forever preferred_lft forever
> >     2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master
> vmbr1224 state UP group default
> >     qlen 1000
> >         link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
> >         altname enp24s0f0
> >     3: enp59s0f4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq
> state UP group default qlen 1000
> >         link/ether 00:07:43:18:82:70 brd ff:ff:ff:ff:ff:ff
> >         inet6 fe80::207:43ff:fe18:8270/64 scope link
> >            valid_lft forever preferred_lft forever
> >     4: enp59s0f4d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq
> state UP group default qlen 1000
> >         link/ether 00:07:43:18:82:78 brd ff:ff:ff:ff:ff:ff
> >         inet6 fe80::207:43ff:fe18:8278/64 scope link
> >            valid_lft forever preferred_lft forever
> >     5: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
> default qlen 1000
> >         link/ether a4:bf:01:2f:63:f3 brd ff:ff:ff:ff:ff:ff
> >         altname enp24s0f1
> >     6: ibp94s0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN
> group default qlen 256
> >         link/infiniband
> 80:00:0a:08:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:51 brd
> >     00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> >     7: ibp94s0d1: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN
> group default qlen 256
> >         link/infiniband
> 80:00:0a:09:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:52 brd
> >     00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> >     8: vmbr1224: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
> noqueue state UP group default
> >     qlen 1000
> >         link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
> >         inet 10.224.203.1/16 <http://10.224.203.1/16> scope global
> vmbr1224
> >            valid_lft forever preferred_lft forever
> >         inet6 fe80::a6bf:1ff:fe2f:63f2/64 scope link
> >            valid_lft forever preferred_lft forever
> >
> >
> >     My current /etc/network/interfaces, which is missing the bridges for
> the VMs:
> >     auto lo
> >     iface lo inet loopback
> >
> >     auto eno1
> >     iface eno1 inet manual
> >
> >     auto enp59s0f4
> >     iface enp59s0f4 inet manual
> >       mtu 9000
> >
> >     auto enp59s0f4d1
> >     iface enp59s0f4d1 inet manual
> >       mtu 9000
> >
> >     auto bond0
> >     iface bond0 inet manual
> >       slaves enp59s0f4 enp59s0f4d1
> >       bond-downdelay 200
> >       bond-miimon 100
> >       bond-mode 802.3ad
> >       bond-updelay 200
> >
> >     auto vmbr1224
> >     iface vmbr1224 inet static
> >       address 10.224.203.1
> >       netmask 255.255.0.0
> >       gateway 10.224.200.1
> >       bridge_ports eno1
> >       bridge_stp off
> >       bridge_fd 0
> >
> >     ##  # VLAN 155 nativ on bond0
> >     ##  auto vmbr155
> >     ##  iface vmbr155 inet manual
> >     ##    mtu 9000
> >     ##    bridge_ports bond0
> >     ##    bridge_stp off
> >     ##    bridge_fd 0
> >
> >
> >     This config was copied over from the PVE 6 installation on the same
> host which experienced a SSD
> >     failure and thus was re-installed with PVE 7.
> >
> >
> >     Am I missing something? Am I being blind?
> >
> >
> >     Any help is appreciated.
> >
> >
> >     Thanks,
> >
> >             Uwe
> >
> >
> >
> >
> >     _______________________________________________
> >     pve-user mailing list
> >     pve-user@lists.proxmox.com <mailto:pve-user@lists.proxmox.com>
> >     https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
> >     <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user>
> >
>
>