* [PVE-User] OS Error after upgrade to 7.1 @ 2021-11-23 13:04 Ralf Storm 2021-11-23 13:14 ` Uwe Sauter 0 siblings, 1 reply; 6+ messages in thread From: Ralf Storm @ 2021-11-23 13:04 UTC (permalink / raw) To: pve-user Hello, I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs to be corrected, but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode setting" Anybody had this error before? Best regards -- Ralf Storm Systemadministrator Konzept Informationssysteme GmbH .... ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PVE-User] OS Error after upgrade to 7.1 2021-11-23 13:04 [PVE-User] OS Error after upgrade to 7.1 Ralf Storm @ 2021-11-23 13:14 ` Uwe Sauter [not found] ` <737e7b21-85e0-f7a8-9dff-a6e0a3470951@konzept-is.de> 0 siblings, 1 reply; 6+ messages in thread From: Uwe Sauter @ 2021-11-23 13:14 UTC (permalink / raw) To: pve-user Am 23.11.21 um 14:04 schrieb Ralf Storm: > Hello, > > I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs to be > corrected, > > but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode setting" > > Anybody had this error before? Yes, unrelated to Proxmox. But the SAS controller works fine even with this message. Do you have issues accessing your storage? > > Best regards > ^ permalink raw reply [flat|nested] 6+ messages in thread
[parent not found: <737e7b21-85e0-f7a8-9dff-a6e0a3470951@konzept-is.de>]
* Re: [PVE-User] OS Error after upgrade to 7.1 [not found] ` <737e7b21-85e0-f7a8-9dff-a6e0a3470951@konzept-is.de> @ 2021-11-23 13:37 ` Uwe Sauter 2021-11-24 10:24 ` Ralf Storm 0 siblings, 1 reply; 6+ messages in thread From: Uwe Sauter @ 2021-11-23 13:37 UTC (permalink / raw) To: Ralf Storm, Proxmox VE user list Am 23.11.21 um 14:34 schrieb Ralf Storm: > Hello, > > > yes - I have a problem, as mentioned in my first mail, the system is stuck at boot with this message > and then after a few minutes reboots... Can you reboot with the previous kernel and check the firmware of the controller? dmesg | grep mpt | grep -i fw should show the firmware version. > > > Am 23/11/2021 um 14:14 schrieb Uwe Sauter: >> Am 23.11.21 um 14:04 schrieb Ralf Storm: >>> Hello, >>> >>> I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs to be >>> corrected, >>> >>> but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode >>> setting" >>> >>> Anybody had this error before? >> Yes, unrelated to Proxmox. But the SAS controller works fine even with this message. >> >> Do you have issues accessing your storage? >> >>> Best regards >>> >> >> _______________________________________________ >> pve-user mailing list >> pve-user@lists.proxmox.com >> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PVE-User] OS Error after upgrade to 7.1 2021-11-23 13:37 ` Uwe Sauter @ 2021-11-24 10:24 ` Ralf Storm [not found] ` <mailman.713.1637764284.15957.pve-user@lists.proxmox.com> 0 siblings, 1 reply; 6+ messages in thread From: Ralf Storm @ 2021-11-24 10:24 UTC (permalink / raw) To: uwe.sauter.de, Proxmox VE user list Hello, Proxmox is starting again after upgrading the firmware of the 9211-8i controllers... And yes it did boot with the old Kernel, so the Firmware of the controllers was incompatible with thie new Kernel. Ralf Storm Systemadministrator Konzept Informationssysteme GmbH Am 23.11.2021 um 14:37 schrieb Uwe Sauter: > Am 23.11.21 um 14:34 schrieb Ralf Storm: >> Hello, >> >> >> yes - I have a problem, as mentioned in my first mail, the system is stuck at boot with this message >> and then after a few minutes reboots... > Can you reboot with the previous kernel and check the firmware of the controller? > > dmesg | grep mpt | grep -i fw > > should show the firmware version. > > >> >> Am 23/11/2021 um 14:14 schrieb Uwe Sauter: >>> Am 23.11.21 um 14:04 schrieb Ralf Storm: >>>> Hello, >>>> >>>> I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs to be >>>> corrected, >>>> >>>> but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode >>>> setting" >>>> >>>> Anybody had this error before? >>> Yes, unrelated to Proxmox. But the SAS controller works fine even with this message. >>> >>> Do you have issues accessing your storage? >>> >>>> Best regards >>>> >>> _______________________________________________ >>> pve-user mailing list >>> pve-user@lists.proxmox.com >>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user ^ permalink raw reply [flat|nested] 6+ messages in thread
[parent not found: <mailman.713.1637764284.15957.pve-user@lists.proxmox.com>]
* Re: [PVE-User] OS Error after upgrade to 7.1 [not found] ` <mailman.713.1637764284.15957.pve-user@lists.proxmox.com> @ 2021-11-24 14:45 ` Ralf Storm 2021-11-24 15:36 ` Uwe Sauter 0 siblings, 1 reply; 6+ messages in thread From: Ralf Storm @ 2021-11-24 14:45 UTC (permalink / raw) To: pve-user Hello Stefan, I had the old Firmware (from2015?) 000..26 - the ri version not the it version - this did not work on the 5.13 Kernel - stuck at boot and server rebooting after a while the newest version i found was from 2016 000..27 , which works, it is hard to find any firmwares as the vendor does not supply it anymore, there are descriptions howto update and links to the firmware, but the links are dead... Has to be updated in efi shell from usb drive hope that helps, best regards Ralf Hi Ralf Would you mind to share the old and new firmware versions of your controller and your kernel version? It might help other PVE users to avoid the problem you have run into. Thank you Stefan > On Nov 24, 2021, at 11:24, Ralf Storm<ralf.storm@konzept-is.de> wrote: > > Hello, > > > Proxmox is starting again after upgrading the firmware of the 9211-8i controllers... > > And yes it did boot with the old Kernel, so the Firmware of the controllers was incompatible with thie new Kernel. > > > Ralf Storm > > > Systemadministrator > > > > Konzept Informationssysteme GmbH > > Am 23.11.2021 um 14:37 schrieb Uwe Sauter: >> Am 23.11.21 um 14:34 schrieb Ralf Storm: >>> Hello, >>> >>> >>> yes - I have a problem, as mentioned in my first mail, the system is stuck at boot with this message >>> and then after a few minutes reboots... >> Can you reboot with the previous kernel and check the firmware of the controller? >> >> dmesg | grep mpt | grep -i fw >> >> should show the firmware version. >> >> >>> Am 23/11/2021 um 14:14 schrieb Uwe Sauter: >>>> Am 23.11.21 um 14:04 schrieb Ralf Storm: >>>>> Hello, >>>>> >>>>> I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs to be >>>>> corrected, >>>>> >>>>> but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode >>>>> setting" >>>>> >>>>> Anybody had this error before? >>>> Yes, unrelated to Proxmox. But the SAS controller works fine even with this message. >>>> >>>> Do you have issues accessing your storage? >>>> >>>>> Best regards >>>>> >>>> _______________________________________________ >>>> pve-user mailing list >>>> pve-user@lists.proxmox.com >>>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > _______________________________________________ > pve-user mailing list > pve-user@lists.proxmox.com > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PVE-User] OS Error after upgrade to 7.1 2021-11-24 14:45 ` Ralf Storm @ 2021-11-24 15:36 ` Uwe Sauter 0 siblings, 0 replies; 6+ messages in thread From: Uwe Sauter @ 2021-11-24 15:36 UTC (permalink / raw) To: Proxmox VE user list, Ralf Storm Am 24.11.21 um 15:45 schrieb Ralf Storm: > Hello Stefan, > > I had the old Firmware (from2015?) 000..26 - the ri version not the it version - this did not work > on the 5.13 Kernel - stuck at boot and server rebooting after a while > > the newest version i found was from 2016 000..27 , which works, it is hard to find any firmwares as > the vendor does not supply it anymore, there are descriptions howto update and links to the > firmware, but the links are dead... > If you go to https://www.broadcom.com/support/download-search and then: Product Group -> Legacy Products (all the way down) Product Family -> Legacy Host Bus Adapters Product Name -> SAS 9211-8i Host Bus Adapter => Search you will find all firmware versions and related tools, docs, etc. that Broadcom shares. The latest available firmware is 20.00.07.00 dated 2016-04-04. > Has to be updated in efi shell from usb drive > > > hope that helps, > > best regards > > Ralf > > > Hi Ralf > > Would you mind to share the old and new firmware versions of your controller and your kernel version? > > It might help other PVE users to avoid the problem you have run into. > > Thank you > > Stefan > >> On Nov 24, 2021, at 11:24, Ralf Storm<ralf.storm@konzept-is.de> wrote: >> >> Hello, >> >> >> Proxmox is starting again after upgrading the firmware of the 9211-8i controllers... >> >> And yes it did boot with the old Kernel, so the Firmware of the controllers was incompatible with >> thie new Kernel. >> >> >> Ralf Storm >> >> >> Systemadministrator >> >> >> >> Konzept Informationssysteme GmbH >> >> Am 23.11.2021 um 14:37 schrieb Uwe Sauter: >>> Am 23.11.21 um 14:34 schrieb Ralf Storm: >>>> Hello, >>>> >>>> >>>> yes - I have a problem, as mentioned in my first mail, the system is stuck at boot with this >>>> message >>>> and then after a few minutes reboots... >>> Can you reboot with the previous kernel and check the firmware of the controller? >>> >>> dmesg | grep mpt | grep -i fw >>> >>> should show the firmware version. >>> >>> >>>> Am 23/11/2021 um 14:14 schrieb Uwe Sauter: >>>>> Am 23.11.21 um 14:04 schrieb Ralf Storm: >>>>>> Hello, >>>>>> >>>>>> I´m currently upgrading my 7-node Cluster, 1 node without problems, 2 nodes had renamed NICs >>>>>> to be >>>>>> corrected, >>>>>> >>>>>> but the last Node stucks at boot with this message: "mpt2sas_cm0: overiding NVDATA EEDPTagMode >>>>>> setting" >>>>>> >>>>>> Anybody had this error before? >>>>> Yes, unrelated to Proxmox. But the SAS controller works fine even with this message. >>>>> >>>>> Do you have issues accessing your storage? >>>>> >>>>>> Best regards >>>>>> >>>>> _______________________________________________ >>>>> pve-user mailing list >>>>> pve-user@lists.proxmox.com >>>>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user >> _______________________________________________ >> pve-user mailing list >> pve-user@lists.proxmox.com >> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > _______________________________________________ > pve-user mailing list > pve-user@lists.proxmox.com > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-11-24 15:37 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-11-23 13:04 [PVE-User] OS Error after upgrade to 7.1 Ralf Storm
2021-11-23 13:14 ` Uwe Sauter
[not found] ` <737e7b21-85e0-f7a8-9dff-a6e0a3470951@konzept-is.de>
2021-11-23 13:37 ` Uwe Sauter
2021-11-24 10:24 ` Ralf Storm
[not found] ` <mailman.713.1637764284.15957.pve-user@lists.proxmox.com>
2021-11-24 14:45 ` Ralf Storm
2021-11-24 15:36 ` Uwe Sauter
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox