From: "Fabian Grünbichler" <f.gruenbichler@proxmox.com>
To: Proxmox VE development discussion <pve-devel@lists.proxmox.com>
Subject: Re: [pve-devel] [PATCH pve-manager master v1 2/2] fix #6652: d/postinst: enable autoactivation for Ceph OSD LVs
Date: Wed, 13 Aug 2025 12:05:25 +0200 [thread overview]
Message-ID: <1755079310.1zhsa6x31t.astroid@yuna.none> (raw)
In-Reply-To: <DC178DJFU5K3.2UVPMMNXGASPJ@proxmox.com>
On August 13, 2025 11:40 am, Max R. Carrara wrote:
> On Wed Aug 13, 2025 at 11:02 AM CEST, Fabian Grünbichler wrote:
>> On August 13, 2025 10:50 am, Max R. Carrara wrote:
>> > On Wed Aug 13, 2025 at 9:52 AM CEST, Fabian Grünbichler wrote:
>> >> On August 12, 2025 6:46 pm, Max R. Carrara wrote:
>> >> > Introduce a new helper command pve-osd-lvm-enable-autoactivation,
>> >> > which gracefully tries to enable autoactivation for all logical
>> >> > volumes used by Ceph OSDs while also activating any LVs that aren't
>> >> > active yet. Afterwards, the helper attempts to bring all OSDs online.
>> >>
>> >> I think this is probably overkill - this only affects a specific non
>> >> standard setup, the breakage is really obvious, and the fix is easy:
>> >> either run lvchange on all those LVs, or recreate the OSDs after the fix
>> >> for creation is rolled out..
>> >>
>> >> i.e., the fallout from some edge cases not being handled correctly in
>> >> the 200 line helper script here is probably worse than the few setups
>> >> that run into the original issue that we can easily help along
>> >> manually..
>> >
>> > I mean, this script doesn't really do much, and the LVs themselves are
>> > fetched via `ceph-volume` ... But then again, you're probably right that
>> > it might just break somebody else's arcane setup somewhere.
>> >
>> > As an alternative, I wouldn't mind writing something for the release
>> > notes' known issues section (or some other place). Assuming a standard
>> > setup*, all that the user would have to do is identical to what the
>> > script does, so nothing too complicated.
>>
>> but the known issue will be gone, except for the handful of users that
>> ran into it before the fix was rolled out.. this is not something you
>> noticed 5 months later?
>
> Are you sure, though? There might very well be setups out there that are
> only rebooted every couple months or so--not everybody is as diligent
> with their maintenance, unfortunately. We don't really know how common /
> rare it is to set up a DB / WAL disk for OSDs.
I am not opposed to adding it to the known issues, I just think it's not
a very common issue to run into in the first place.
>> > (*OSDs with WAL + DB on disks / partitions without anything else inbetween)
>>
>> I am not worried about the script breaking things, but about it printing
>> spurious errors/warnings for unaffected setups.
>
> Well, unaffected here would mean that all OSD LVs have autoactivation
> enabled (and are also activated). Additionally, if the OSDs are already
> up, `ceph-volume` doesn't do anything either.
no, unaffected here means 99% of the systems. and as soon as you run
commands on any system, there will be a small percentage where those
commands fail in noisy fashion for whatever reason. so the tradeoff
needs to be there - if the issue is big enough and the commands are not
very involved, then yes, fixing in postinst like this is a good idea.
for an issue that will affect almost nobody, and that requires running
commands with lots of storage interaction(!), that tradeoff looks rather
different..
> FWIW we could suppress LVM "No medium found" warnings in the LVM
> commands the script runs, like we do in pve-storage [0]. Additionally,
> we could also short-circuit and silently exit early if no changes are
> necessary; e.g. if autoactivation is enabled for all OSD LVs, we can
> assume that they're activated as well, and that the OSDs themselves are
> therefore running, too.
>
> So, I would really prefer having either (an improved version of) the
> script, or some documentation regarding this *somewhere*, just to not
> leave any users in the dark.
>
> [0]: https://git.proxmox.com/?p=pve-storage.git;a=blob;f=src/PVE/Storage/LVMPlugin.pm;h=0416c9e02a1d8255c940d2cd9f5e0111b784fe7c;hb=refs/heads/master#l21
>
>>
>>
>> _______________________________________________
>> pve-devel mailing list
>> pve-devel@lists.proxmox.com
>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
>
>
>
> _______________________________________________
> pve-devel mailing list
> pve-devel@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
>
_______________________________________________
pve-devel mailing list
pve-devel@lists.proxmox.com
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
next prev parent reply other threads:[~2025-08-13 10:04 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-12 16:46 [pve-devel] [PATCH pve-manager master v1 0/2] Fix #6652: LVM Autoactivation Missing " Max R. Carrara
2025-08-12 16:46 ` [pve-devel] [PATCH pve-manager master v1 1/2] fix #6652: ceph: osd: enable autoactivation for OSD LVs on creation Max R. Carrara
2025-08-13 7:48 ` Fabian Grünbichler
2025-08-13 8:28 ` Max R. Carrara
2025-08-12 16:46 ` [pve-devel] [PATCH pve-manager master v1 2/2] fix #6652: d/postinst: enable autoactivation for Ceph OSD LVs Max R. Carrara
2025-08-13 7:52 ` Fabian Grünbichler
2025-08-13 8:50 ` Max R. Carrara
2025-08-13 9:01 ` Friedrich Weber
2025-08-13 9:02 ` Fabian Grünbichler
2025-08-13 9:40 ` Max R. Carrara
2025-08-13 10:05 ` Fabian Grünbichler [this message]
2025-08-13 13:43 ` [pve-devel] superseded: [PATCH pve-manager master v1 0/2] Fix #6652: LVM Autoactivation Missing " Max R. Carrara
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1755079310.1zhsa6x31t.astroid@yuna.none \
--to=f.gruenbichler@proxmox.com \
--cc=pve-devel@lists.proxmox.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox