Re: [PVE-User] openvswitch + bond0 + 2 Fiber interfaces.

[Dimitri Alexandris <d.alexandris@gmail.com>]

I have Openvswitch bonds working fine for years now, but in older versions
of Proxmox (6.4-4 and 5.3-5):

--------------
auto eno2
iface eno2 inet manual

auto eno1
iface eno1 inet manual

allow-vmbr0 ath
iface ath inet static
address 10.NN.NN.38/26
gateway 10.NN.NN.1
ovs_type OVSIntPort
ovs_bridge vmbr0
ovs_options tag=100
.
.
allow-vmbr0 bond0
iface bond0 inet manual
  ovs_bonds eno1 eno2
  ovs_type OVSBond
  ovs_bridge vmbr0
  ovs_options bond_mode=balance-slb lacp=active
allow-ovs vmbr0
iface vmbr0 inet manual
ovs_type OVSBridge
ovs_ports bond0 ath lan dmz_vod ampr
--------

I think now, "allow-vmbr0" and "allow-ovs" are replaced with "auto".

This bond works fine with HP, 3COM, HUAWEI, and MIKROTIK switches.
Several OVSIntPort VLANS are attached to it.
I also had 10G bonds (Intel, Supermicro inter-server links), with the same
result.

I see the only difference with your setup is the bond_mode.  Switch setup
is also very important to match this.





On Fri, Jan 21, 2022 at 1:23 PM Сергей Цаболов <tsabolov@t8.ru> wrote:

> Hello,
>
> I have PVE cluster and I thinking to install on  the pve-7 openvswitch
> for can move and add VM from other networks and Proxmox Cluster
>
> With base Linux bridge all work well without problem with 2 interface
> 10GB ens1f0np0 ens1f12np0
>
> I  install openvswitch  with manual
> https://pve.proxmox.com/wiki/Open_vSwitch
>
> I want use Fiber  10GB interfaces ens1f0np0 ens1f12np0  with Bond I think.
>
> I try some settings but is not working.
>
> My setup in interfaces:
>
> auto lo
> iface lo inet loopback
>
> auto ens1f12np0
> iface ens1f12np0 inet manual
> #Fiber
>
> iface idrac inet manual
>
> iface eno2 inet manual
>
> iface eno3 inet manual
>
> iface eno4 inet manual
>
> auto ens1f0np0
> iface ens1f0np0 inet manual
>
> iface eno1 inet manual
>
> auto inband
> iface inband inet static
>      address 10.10.29.10/24
>      gateway 10.10.29.250
>      ovs_type OVSIntPort
>      ovs_bridge vmbr0
> #Proxmox Web Access
>
> auto vlan10
> iface vlan10 inet manual
>      ovs_type OVSIntPort
>      ovs_bridge vmbr0
>      ovs_options tag=10
> #Network 10
>
> auto bond0
> iface bond0 inet manual
>      ovs_bonds ens1f0np0 ens1f12np0
>      ovs_type OVSBond
>      ovs_bridge vmbr0
>      ovs_mtu 9000
>      ovs_options bond_mode=active-backup
>
> auto vmbr0
> iface vmbr0 inet manual
>      ovs_type OVSBridge
>      ovs_ports bond0 inband vlan10
>      ovs_mtu 9000
> #inband
>
>
> Can some one help me if I set all correctly or not?
>
> If someone have setup openvswitch with Bond interfaces 10GB share with
> me configuration.
>
> Thank at lot.
>
>
> Sergey TS
> The best Regard
>
> _______________________________________________
> pve-user mailing list
> pve-user@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>
> _______________________________________________
> pve-user mailing list
> pve-user@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>