Re: [PVE-User] openvswitch + bond0 + 2 Fiber interfaces.

["Сергей Цаболов" <tsabolov@t8.ru>]

Hello,

I have before 30 min this problem.

I complete the interfaces edit by cli.

But I have problem when I try to edit from GUI something like add 
comment or add new OVS Bridge or new OVS IntPort (new lan)

GUI answer something like

# OVS bond 'bond0' - wrong interface type on slave 'ens1f0np0' ('' != 
'eth') (500)
# OVS bond 'bond1' - wrong interface type on slave 'eno1' ('' != 'eth') 
(500)

Below my Interfaces :

auto lo
iface lo inet loopback

auto ens1f0np0
iface ens1f0np0 inet manual
     ovs_type OVSPort
     ovs_mtu 9000
#Fiber

auto ens1f12np0
iface ens1f12np0 inet manual
     ovs_type OVSPort
     ovs_mtu  9000
#Fiber

auto eno1
iface eno1 inet manual
     ovs_type OVSPort

auto eno2
iface eno2 inet manual
     ovs_type OVSPort

auto vlan10
iface vlan10 inet static
     address 10.10.29.10/24
     gateway 10.10.29.250
     ovs_type OVSIntPort
     ovs_bridge vmbr0
     ovs_mtu 9000
     ovs_options tag=10
     ovs_extra set interface ${IFACE} external-ids:iface-id=$(hostname 
-s)-${IFACE}-vif

auto vlan29
iface vlan29 inet static
     address 192.168.29.96/24
     ovs_type OVSIntPort
     ovs_bridge vmbr1
     ovs_mtu 1500
     ovs_options tag=29
     ovs_extra set interface ${IFACE} external-ids:iface-id=$(hostname 
-s)-${IFACE}-vif

auto vlan250
iface vlan250 inet static
     address 192.168.250.100/24
     ovs_type OVSIntPort
     ovs_bridge vmbr0
     ovs_mtu 9000
     ovs_options tag=250
     ovs_extra set interface ${IFACE} external-ids:iface-id=$(hostname 
-s)-${IFACE}-vif

auto bond0
iface bond0 inet manual
     ovs_type OVSBond
     ovs_bridge vmbr0
     ovs_bonds ens1f0np0    ens1f12np0
     ovs_options trunks=10,29,250 bond_mode=active-backup
     ovs_mtu        9000
#Fiber

auto bond1
iface bond1 inet manual
     ovs_type OVSBond
     ovs_bridge vmbr1
     ovs_bonds eno1    eno2
     ovs_options bond_mode=active-backup
     ovs_mtu    1500


auto vmbr0
iface vmbr0 inet manual
     ovs_type OVSBridge
     ovs_ports bond0 vlan10 vlan250
     ovs_mtu 9000

auto vmbr1
iface vmbr1 inet manual
     ovs_type OVSBridge
     ovs_ports bond1 vlan29
     ovs_mtu 1500


----------------------------------------------------------------------------

Now I found solution :

In interfaces wrong is ovs_type OVSPort if we comment it out or remove 
the GUI worked fine.

auto ens1f0np0
iface ens1f0np0 inet manual
#    ovs_type OVSPort
#    ovs_mtu 9000
#Fiber

auto ens1f12np0
iface ens1f12np0 inet manual
#    ovs_type OVSPort
#    ovs_mtu  9000
#Fiber

auto eno1
iface eno1 inet manual
#    ovs_type OVSPort

auto eno2
iface eno2 inet manual
#    ovs_type OVSPort


21.01.2022 15:28, Сергей Цаболов пишет:
> Dimitri, hello
>
> Thank you with you share
>
> My Proxmox  is proxmox-ve: 6.4-1 (running kernel: 5.4.143-1-pve)
>
> I try change allow-vmbr0 with auto.
>
> I found the link 
> https://metadata.ftp-master.debian.org/changelogs/main/o/openvswitch/testing_openvswitch-switch.README.Debian 
>
>
> In section  ex 9: Bond + Bridge + VLAN + MTU  allow is used.
>
> But nothing wrong I try allow and auto, just comment one line.
>
>
> Dimitri, thanks again for you share.
>
>
>
>
> 21.01.2022 15:03, Dimitri Alexandris пишет:
>> I have Openvswitch bonds working fine for years now, but in older 
>> versions
>> of Proxmox (6.4-4 and 5.3-5):
>>
>> --------------
>> auto eno2
>> iface eno2 inet manual
>>
>> auto eno1
>> iface eno1 inet manual
>>
>> allow-vmbr0 ath
>> iface ath inet static
>> address 10.NN.NN.38/26
>> gateway 10.NN.NN.1
>> ovs_type OVSIntPort
>> ovs_bridge vmbr0
>> ovs_options tag=100
>> .
>> .
>> allow-vmbr0 bond0
>> iface bond0 inet manual
>>    ovs_bonds eno1 eno2
>>    ovs_type OVSBond
>>    ovs_bridge vmbr0
>>    ovs_options bond_mode=balance-slb lacp=active
>> allow-ovs vmbr0
>> iface vmbr0 inet manual
>> ovs_type OVSBridge
>> ovs_ports bond0 ath lan dmz_vod ampr
>> --------
>>
>> I think now, "allow-vmbr0" and "allow-ovs" are replaced with "auto".
>>
>> This bond works fine with HP, 3COM, HUAWEI, and MIKROTIK switches.
>> Several OVSIntPort VLANS are attached to it.
>> I also had 10G bonds (Intel, Supermicro inter-server links), with the 
>> same
>> result.
>>
>> I see the only difference with your setup is the bond_mode. Switch setup
>> is also very important to match this.
>>
>>
>>
>>
>>
>> On Fri, Jan 21, 2022 at 1:23 PM Сергей Цаболов<tsabolov@t8.ru>  wrote:
>>
>>> Hello,
>>>
>>> I have PVE cluster and I thinking to install on  the pve-7 openvswitch
>>> for can move and add VM from other networks and Proxmox Cluster
>>>
>>> With base Linux bridge all work well without problem with 2 interface
>>> 10GB ens1f0np0 ens1f12np0
>>>
>>> I  install openvswitch  with manual
>>> https://pve.proxmox.com/wiki/Open_vSwitch
>>>
>>> I want use Fiber  10GB interfaces ens1f0np0 ens1f12np0  with Bond I 
>>> think.
>>>
>>> I try some settings but is not working.
>>>
>>> My setup in interfaces:
>>>
>>> auto lo
>>> iface lo inet loopback
>>>
>>> auto ens1f12np0
>>> iface ens1f12np0 inet manual
>>> #Fiber
>>>
>>> iface idrac inet manual
>>>
>>> iface eno2 inet manual
>>>
>>> iface eno3 inet manual
>>>
>>> iface eno4 inet manual
>>>
>>> auto ens1f0np0
>>> iface ens1f0np0 inet manual
>>>
>>> iface eno1 inet manual
>>>
>>> auto inband
>>> iface inband inet static
>>>       address 10.10.29.10/24
>>>       gateway 10.10.29.250
>>>       ovs_type OVSIntPort
>>>       ovs_bridge vmbr0
>>> #Proxmox Web Access
>>>
>>> auto vlan10
>>> iface vlan10 inet manual
>>>       ovs_type OVSIntPort
>>>       ovs_bridge vmbr0
>>>       ovs_options tag=10
>>> #Network 10
>>>
>>> auto bond0
>>> iface bond0 inet manual
>>>       ovs_bonds ens1f0np0 ens1f12np0
>>>       ovs_type OVSBond
>>>       ovs_bridge vmbr0
>>>       ovs_mtu 9000
>>>       ovs_options bond_mode=active-backup
>>>
>>> auto vmbr0
>>> iface vmbr0 inet manual
>>>       ovs_type OVSBridge
>>>       ovs_ports bond0 inband vlan10
>>>       ovs_mtu 9000
>>> #inband
>>>
>>>
>>> Can some one help me if I set all correctly or not?
>>>
>>> If someone have setup openvswitch with Bond interfaces 10GB share with
>>> me configuration.
>>>
>>> Thank at lot.
>>>
>>>
>>> Sergey TS
>>> The best Regard
>>>
>>> _______________________________________________
>>> pve-user mailing list
>>> pve-user@lists.proxmox.com
>>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>>>
>>> _______________________________________________
>>> pve-user mailing list
>>> pve-user@lists.proxmox.com
>>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>>>
>> _______________________________________________
>> pve-user mailing list
>> pve-user@lists.proxmox.com
>> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>
> Sergey TS
> The best Regard
>
> _______________________________________________
> pve-user mailing list
> pve-user@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
> _______________________________________________
> pve-user mailing list
> pve-user@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user

Sergey TS
The best Regard

_______________________________________________
pve-user mailing list
pve-user@lists.proxmox.com
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user