From: "Alexander Zeidler" <a.zeidler@proxmox.com>
To: "Proxmox VE development discussion" <pve-devel@lists.proxmox.com>
Subject: Re: [pve-devel] [PATCH docs 1/6] ceph: add anchors for use in troubleshooting section
Date: Wed, 05 Feb 2025 11:10:49 +0100 [thread overview]
Message-ID: <D7KFITL9ZXJY.2AN6I73UG8JR5@proxmox.com> (raw)
In-Reply-To: <D7JKIHEE0XZW.1WGVRUD004T88@proxmox.com>
On Tue Feb 4, 2025 at 10:52 AM CET, Max Carrara wrote:
> On Tue Feb 4, 2025 at 10:22 AM CET, Alexander Zeidler wrote:
>> On Mon Feb 3, 2025 at 5:19 PM CET, Max Carrara wrote:
>> > On Mon Feb 3, 2025 at 3:27 PM CET, Alexander Zeidler wrote:
>> >> Signed-off-by: Alexander Zeidler <a.zeidler@proxmox.com>
>> >> ---
>> >
>> > Some high-level feedback (see comments inline and in patches otherwise):
>> >
>> > - The writing style is IMO quite clear and straightforward, nice work!
>> Thank you for the review!
>>
>> >
>> > - In patch 03, the "_disk_health_monitoring" anchor reference seems to
>> > break my build for some reason. Does this also happen on your end? The
>> > single-page docs ("pve-admin-guide.html") seem to build just fine
>> > otherwise.
>> Same for me, I will fix it.
>>
>> >
>> > - Regarding implicitly / auto-generated anchors, is it fine to break
>> > those in general or not? See my other comments inline here.
>> >
>> > - There are a few tiny style things I personally would correct, but if
>> > you disagree with them, feel free to leave them as they are.
>> I will look into it! Using longer link texts sounds good!
>>
>> >
>> > All in all this seems pretty solid; the stuff regarding the anchors
>> > needs to be clarified first (whether it's okay to break auto-generated
>> > ones & the one anchor that makes my build fail). Otherwise, pretty good!
>> See my two comments below.
>>
>> >
>> >> pveceph.adoc | 8 ++++++++
>> >> 1 file changed, 8 insertions(+)
>> >>
>> >> diff --git a/pveceph.adoc b/pveceph.adoc
>> >> index da39e7f..93c2f8d 100644
>> >> --- a/pveceph.adoc
>> >> +++ b/pveceph.adoc
>> >> @@ -82,6 +82,7 @@ and vocabulary
>> >> footnote:[Ceph glossary {cephdocs-url}/glossary].
>> >>
>> >>
>> >> +[[pve_ceph_recommendation]]
>> >> Recommendations for a Healthy Ceph Cluster
>> >> ------------------------------------------
>> >
>> > AsciiDoc automatically generated an anchor for the heading above
>> > already, and it's "_recommendations_for_a_healthy_ceph_cluster"
>> > apparently. So, there's no need to provide one here explicitly, since it
>> > already exists; it also might break old links that refer to the
>> > documentation.
>> For this I searched our forum before, it shows 12 results, the heading
>> was only added about a year ago. But apart from this specific anchor,
>> IMHO it can be okay to break such links in certain cases:
>>
>> * The main reasons for not using the auto generated ones are, that those
>> are not stable (in case of changing the title) and can also be very
>> long when using it with xref:...[...]. Such lines get even longer (and
>> an awkward combined name) when using it as a prefix for sub sections
>> (as often done).
>> * Since with the break there might have been added new or updated
>> information in those chapters/sections, old forum posts may no longer
>> be accurate anyway.
>> * In the Ceph chapter for example, we have been using the explicit
>> "pve_ceph_" or "pveceph_" for years, so IMHO it should (almost
>> always?) be added with adding a new section.
>>
>> >
>> > Though, perhaps in a separate series, you could look for all implicitly
>> > defined anchors and set them explicitly..? Not sure if that's something
>> > we want, though.
>> This would break a lot of links at the same time, so far I am not aware
>> about a notable benefit.
>>
>
> I agree with all of your points made here; so, all in all, great work!
> Ping me when you shoot out v2, then I'll have one last look. :)
v2: https://lore.proxmox.com/pve-devel/20250205100850.3-1-a.zeidler@proxmox.com/T/#t
>
>
>
> _______________________________________________
> pve-devel mailing list
> pve-devel@lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
_______________________________________________
pve-devel mailing list
pve-devel@lists.proxmox.com
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
prev parent reply other threads:[~2025-02-05 10:10 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-02-03 14:27 [pve-devel] [PATCH docs 1/6] ceph: add anchors for use in troubleshooting section Alexander Zeidler
2025-02-03 14:27 ` [pve-devel] [PATCH docs 2/6] ceph: correct heading capitalization Alexander Zeidler
2025-02-03 14:27 ` [pve-devel] [PATCH docs 3/6] ceph: troubleshooting: revise and add frequently needed information Alexander Zeidler
2025-02-03 16:19 ` Max Carrara
2025-02-03 14:27 ` [pve-devel] [PATCH docs 4/6] ceph: osd: revise and expand the section "Destroy OSDs" Alexander Zeidler
2025-02-03 16:19 ` Max Carrara
2025-02-03 14:28 ` [pve-devel] [PATCH docs 5/6] ceph: maintenance: revise and expand section "Replace OSDs" Alexander Zeidler
2025-02-03 14:28 ` [pve-devel] [PATCH docs 6/6] pvecm: remove node: mention Ceph and its steps for safe removal Alexander Zeidler
2025-02-03 16:19 ` [pve-devel] [PATCH docs 1/6] ceph: add anchors for use in troubleshooting section Max Carrara
2025-02-04 9:22 ` Alexander Zeidler
2025-02-04 9:52 ` Max Carrara
2025-02-05 10:10 ` Alexander Zeidler [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=D7KFITL9ZXJY.2AN6I73UG8JR5@proxmox.com \
--to=a.zeidler@proxmox.com \
--cc=pve-devel@lists.proxmox.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox